PowerDesigner设计Name和注释相互替换

野性酷女 2023-10-18 15:52 96阅读 0赞

## PowerDesigner设计Name和注释相互替换 ##

转自:[https://blog.csdn.net/superhoy/article/details/13018717?locationNum=13][https_blog.csdn.net_superhoy_article_details_13018717_locationNum_13]

[PowerDesigner][]设计 设计的表

Name是名称（字段描述），Code是字段名称，Comment是注释名称，ER图中显示的是Name。一般设计时，Name跟comment都设计成描述，

而设计时候常把comment写成中文，name保留跟code一致，保存完毕后，可以把comment替换到name上。当然也可以用name替换comment。具体方法如下：

1　将comment覆盖name

Option   Explicit 
    ValidationMode   =   True 
    InteractiveMode   =   im_Batch
    Dim   mdl   '   the   current   model
    '   get   the   current   active   model 
    Set   mdl   =   ActiveModel 
    If   (mdl   Is   Nothing)   Then 
          MsgBox   "There   is   no   current   Model " 
    ElseIf   Not   mdl.IsKindOf(PdPDM.cls_Model)   Then 
          MsgBox   "The   current   model   is   not   an   Physical   Data   model. " 
    Else 
          ProcessFolder   mdl 
    End   If
    Private   sub   ProcessFolder(folder) 
    On Error Resume Next
          Dim   Tab   'running     table 
          for   each   Tab   in   folder.tables 
                if   not   tab.isShortcut   then 
                      tab.name   =   tab.comment
                      Dim   col   '   running   column 
                      for   each   col   in   tab.columns 
                      if col.comment="" then
                      else
                            col.name=   col.comment 
                      end if
                      next 
                end   if 
          next
          Dim   view   'running   view 
          for   each   view   in   folder.Views 
                if   not   view.isShortcut   then 
                      view.name   =   view.comment 
                end   if 
          next
          '   go   into   the   sub-packages 
          Dim   f   '   running   folder 
          For   Each   f   In   folder.Packages 
                if   not   f.IsShortcut   then 
                      ProcessFolder   f 
                end   if 
          Next 
    end   sub

2 将name覆盖comment

Option   Explicit 
    ValidationMode   =   True 
    InteractiveMode   =   im_Batch
    Dim   mdl   '   the   current   model
    '   get   the   current   active   model 
    Set   mdl   =   ActiveModel 
    If   (mdl   Is   Nothing)   Then 
          MsgBox   "There   is   no   current   Model " 
    ElseIf   Not   mdl.IsKindOf(PdPDM.cls_Model)   Then 
          MsgBox   "The   current   model   is   not   an   Physical   Data   model. " 
    Else 
          ProcessFolder   mdl 
    End   If
    '   This   routine   copy   name   into   comment   for   each   table,   each   column   and   each   view 
    '   of   the   current   folder 
    Private   sub   ProcessFolder(folder) 
          Dim   Tab   'running     table 
          for   each   Tab   in   folder.tables 
                if   not   tab.isShortcut   then 
                      tab.comment   =   tab.name 
                      Dim   col   '   running   column 
                      for   each   col   in   tab.columns 
                            col.comment=   col.name 
                      next 
                end   if 
          next
          Dim   view   'running   view 
          for   each   view   in   folder.Views 
                if   not   view.isShortcut   then 
                      view.comment   =   view.name 
                end   if 
          next
          '   go   into   the   sub-packages 
          Dim   f   '   running   folder 
          For   Each   f   In   folder.Packages 
                if   not   f.IsShortcut   then 
                      ProcessFolder   f 
                end   if 
          Next 
    end   sub

以上两段代码都是VB脚本，在PowerDesigner中使用方法为：  
PowerDesigner->Tools->Execute Commands->Edit/Run Scripts 将代码Copy进去执行就可以了，

[https_blog.csdn.net_superhoy_article_details_13018717_locationNum_13]: https://blog.csdn.net/superhoy/article/details/13018717?locationNum=13
[PowerDesigner]: https://www.baidu.com/s?wd=PowerDesigner&tn=24004469_oem_dg&rsv_dl=gh_pl_sl_csd