stm32f4驱动enc28j60（吐槽篇）

今天药忘吃喽~ 2022-09-17 06:23 332阅读 0赞

鼓捣enc28j60这个模块过程还是比较曲折的！

买这个模块的时候，卖家只附送了51的驱动工程。或者说，就51的工程能用！

在51上，一编译一下载就搞定了！

========================吐槽下==============================

在F4这个平台上呢！因为enc28j60.c这个文件的问题，导致我创建了20多份不同的工程来测试！比较坑爹！

刚开始的时候，想移植51的这个文件，发现改动量太大了，改了一下，测试不成功就放弃之！

再拿野火stm32f103的来移植，还是不成功。发现也有网友有这问题，我跟踪调试，发现mac初始化一直不成功！

只好去拿官方库里面的 lwip 的工程来改。还是不行！ 这下不淡定了！

打算去收集资料！

百度关键字 stm32f4 enc28j60 ，几乎没可用的资料！有的也是用手指头都能数的完的求助贴！

谷歌关键字 stm32f4 enc28j60 ，有惊喜！能看到几个视频，而且要看还得翻墙！

那就翻吧！废了九牛二虎之力，找到了三份源码！其中日本那份下载不了，另外两份倒是下载了。

但是打开一看，又纠结了，一份是linux下的工程。另一份不知道拿什么开发工具写的。不过这两份源码倒是能用！

\----------------------------------------------------------------------------------------------------

重新看了一遍enc28j60的手册，拿之前lcd的工程加上国外的源码重新写吧！

前前后后弄了两天，终于出来了！深感累到不行！

============================END=============================

说点有用的，enc28j60与f4通信比较简单。使用SPI，也就需要四根线就行了。

我的接法是：

PA4 -------------- CS

PA5 -------------- SCK

PA6 -------------- SO

PA7 -------------- SI

来张图：![20131002013511953][]

![20131002014151765][]

ENC28J60.C

#include "ENC28J60.h"
    #include "spi.h"
    #include "lcd.h"
    static uint8_t Enc28j60Bank;
    static uint16_t gNextPacketPtr;
    static uint8_t erxfcon;
    
    
    unsigned char ENC28J60_SendByte(unsigned char dt)
    {
    	while(SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_TXE) == RESET);
    
    	SPI_I2S_SendData(SPI1, dt);
    
    	while(SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_RXNE) == RESET);
        
    	return SPI_I2S_ReceiveData(SPI1);
    }
    
    uint8_t enc28j60ReadOp(uint8_t op, uint8_t address)
    {
    		uint8_t temp;
            enableChip;
            // issue read command
            ENC28J60_SendByte(op | (address & ADDR_MASK));
            temp = ENC28J60_SendByte(0xFF);
            if (address & 0x80)
                temp = ENC28J60_SendByte(0xFF);
    
            // release CS
            disableChip;
            return temp;
    }
    
    void enc28j60WriteOp(uint8_t op, uint8_t address, uint8_t data)
    {
        enableChip;
        ENC28J60_SendByte(op | (address & ADDR_MASK));
        ENC28J60_SendByte(data);
        disableChip;
    }
    
    void enc28j60PowerDown() {
     enc28j60WriteOp(ENC28J60_BIT_FIELD_CLR, ECON1, ECON1_RXEN);
     while(enc28j60Read(ESTAT) & ESTAT_RXBUSY);
     while(enc28j60Read(ECON1) & ECON1_TXRTS);
     enc28j60WriteOp(ENC28J60_BIT_FIELD_SET, ECON2, ECON2_PWRSV);
    }
    
    void enc28j60PowerUp() {
     enc28j60WriteOp(ENC28J60_BIT_FIELD_CLR, ECON2, ECON2_PWRSV);
     while(!enc28j60Read(ESTAT) & ESTAT_CLKRDY);
    }
    
    
    void enc28j60ReadBuffer(uint16_t len, uint8_t* data)
    {
        enableChip;
        ENC28J60_SendByte(ENC28J60_READ_BUF_MEM);
        while (len--) {
            *data++ = ENC28J60_SendByte(0x00);
        }
        disableChip;
        // Remove next line suggested by user epam - not needed
    //    *data='\0';
    }
    
    static uint16_t enc28j60ReadBufferWord() {
        uint16_t result;
        enc28j60ReadBuffer(2, (uint8_t*) &result);
        return result;
    }
    
    
    void enc28j60WriteBuffer(uint16_t len, uint8_t* data)
    {
        enableChip;
        ENC28J60_SendByte(ENC28J60_WRITE_BUF_MEM);
        while (len--)
            ENC28J60_SendByte(*data++);
    
        disableChip;
    }
    
    void enc28j60SetBank(uint8_t address)
    {
        if ((address & BANK_MASK) != Enc28j60Bank) {
            enc28j60WriteOp(ENC28J60_BIT_FIELD_CLR, ECON1, ECON1_BSEL1|ECON1_BSEL0);
            Enc28j60Bank = address & BANK_MASK;
            enc28j60WriteOp(ENC28J60_BIT_FIELD_SET, ECON1, Enc28j60Bank>>5);
        }
    }
    
    uint8_t enc28j60Read(uint8_t address)
    {
            // set the bank
            enc28j60SetBank(address);
            // do the read
            return enc28j60ReadOp(ENC28J60_READ_CTRL_REG, address);
    }
    
    void enc28j60WriteWord(uint8_t address, uint16_t data) {
        enc28j60Write(address, data & 0xff);
        enc28j60Write(address + 1, data >> 8);
    }
    
    // read upper 8 bits
    uint16_t enc28j60PhyReadH(uint8_t address)
    {
    	// Set the right address and start the register read operation
    	enc28j60Write(MIREGADR, address);
    	enc28j60Write(MICMD, MICMD_MIIRD);
            delay_us(15);
    
    	// wait until the PHY read completes
    	while(enc28j60Read(MISTAT) & MISTAT_BUSY);
    
    	// reset reading bit
    	enc28j60Write(MICMD, 0x00);
    	
    	return (enc28j60Read(MIRDH));
    }
    
    
    void enc28j60Write(uint8_t address, uint8_t data)
    {
            // set the bank
            enc28j60SetBank(address);
            // do the write
            enc28j60WriteOp(ENC28J60_WRITE_CTRL_REG, address, data);
    }
    
    
    void enc28j60PhyWrite(uint8_t address, uint16_t data)
    {
            // set the PHY register address
            enc28j60Write(MIREGADR, address);
            // write the PHY data
            enc28j60Write(MIWRL, data);
            enc28j60Write(MIWRH, data>>8);
            // wait until the PHY write completes
            while(enc28j60Read(MISTAT) & MISTAT_BUSY){
                    delay_us(15);
            }
    }
    /*
    static void enc28j60PhyWriteWord(byte address, word data) {
        enc28j60Write(MIREGADR, address);
        //enc28j60WriteByte(MIREGADR, address);
        enc28j60WriteWord(MIWRL, data);
        while (enc28j60ReadByte(MISTAT) & MISTAT_BUSY)
            ;
    }
    */
    void enc28j60clkout(uint8_t clk)
    {
            //setup clkout: 2 is 12.5MHz:
    	enc28j60Write(ECOCON, clk & 0x7);
    }
    
    void enc28j60Init( uint8_t* macaddr )
    {
    	enableChip; // ss=0
    
    	// perform system reset
    	enc28j60WriteOp(ENC28J60_SOFT_RESET, 0, ENC28J60_SOFT_RESET);
    	delay_ms(50);
    	// check CLKRDY bit to see if reset is complete
            // The CLKRDY does not work. See Rev. B4 Silicon Errata point. Just wait.
    	//while(!(enc28j60Read(ESTAT) & ESTAT_CLKRDY));
    	// do bank 0 stuff
    	// initialize receive buffer
    	// 16-bit transfers, must write low byte first
    	// set receive buffer start address
    	gNextPacketPtr = RXSTART_INIT;
            // Rx start
    	enc28j60WriteWord(ERXSTL, RXSTART_INIT);
    	// set receive pointer address
    	enc28j60WriteWord(ERXRDPTL, RXSTART_INIT);
    	// RX end
    	enc28j60WriteWord(ERXNDL, RXSTOP_INIT);
    	// TX start
    	enc28j60WriteWord(ETXSTL, TXSTART_INIT);
    	// TX end
    	enc28j60WriteWord(ETXNDL, TXSTOP_INIT);
    	// do bank 1 stuff, packet filter:
            // For broadcast packets we allow only ARP packtets
            // All other packets should be unicast only for our mac (MAADR)
            //
            // The pattern to match on is therefore
            // Type     ETH.DST
            // ARP      BROADCAST
            // 06 08 -- ff ff ff ff ff ff -> ip checksum for theses bytes=f7f9
            // in binary these poitions are:11 0000 0011 1111
            // This is hex 303F->EPMM0=0x3f,EPMM1=0x30
     
    	//enc28j60Write(ERXFCON, ERXFCON_UCEN|ERXFCON_CRCEN|ERXFCON_PMEN);
            //Change to add ERXFCON_BCEN recommended by epam
    	//enc28j60Write(ERXFCON, ERXFCON_UCEN|ERXFCON_CRCEN|ERXFCON_PMEN|ERXFCON_BCEN);
            erxfcon =  ERXFCON_UCEN|ERXFCON_CRCEN|ERXFCON_PMEN|ERXFCON_BCEN;
    	enc28j60Write(ERXFCON, erxfcon );
    	enc28j60WriteWord(EPMM0, 0x303f);
    	enc28j60WriteWord(EPMCSL, 0xf7f9);
            //
    	// do bank 2 stuff
    	// enable MAC receive
    	enc28j60Write(MACON1, MACON1_MARXEN|MACON1_TXPAUS|MACON1_RXPAUS);
    	// bring MAC out of reset
    	enc28j60Write(MACON2, 0x00);
    	// enable automatic padding to 60bytes and CRC operations
    	enc28j60WriteOp(ENC28J60_BIT_FIELD_SET, MACON3, MACON3_PADCFG0|MACON3_TXCRCEN|MACON3_FRMLNEN);  //|MACON3_FULDPX);
    	// set inter-frame gap (non-back-to-back)
    	enc28j60WriteWord(MAIPGL, 0x0C12);
    	// set inter-frame gap (back-to-back)
    	enc28j60Write(MABBIPG, 0x12);
    	// Set the maximum packet size which the controller will accept
            // Do not send packets longer than MAX_FRAMELEN:
    	enc28j60WriteWord(MAMXFLL, MAX_FRAMELEN);	
    	// do bank 3 stuff
            // write MAC address
            // NOTE: MAC address in ENC28J60 is byte-backward
            enc28j60Write(MAADR5, macaddr[0]);
            enc28j60Write(MAADR4, macaddr[1]);
            enc28j60Write(MAADR3, macaddr[2]);
            enc28j60Write(MAADR2, macaddr[3]);
            enc28j60Write(MAADR1, macaddr[4]);
            enc28j60Write(MAADR0, macaddr[5]);
    	// no loopback of transmitted frames
    	enc28j60PhyWrite(PHCON2, PHCON2_HDLDIS);
    	// switch to bank 0
    	enc28j60SetBank(ECON1);
    	// enable interrutps
    	enc28j60WriteOp(ENC28J60_BIT_FIELD_SET, EIE, EIE_INTIE|EIE_PKTIE);
    	// enable packet reception
    	enc28j60WriteOp(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_RXEN);
    	
    	LCD_String(20,80,"Mac Init",GREEN);
    }
    
    // read the revision of the chip:
    uint8_t enc28j60getrev(void)
    {
            uint8_t rev;
            rev=enc28j60Read(EREVID);
            // microchip forgot to step the number on the silcon when they
            // released the revision B7. 6 is now rev B7. We still have
            // to see what they do when they release B8. At the moment
            // there is no B8 out yet
            if (rev>5) rev++;
    	return(rev);
    }
    
    // A number of utility functions to enable/disable broadcast and multicast bits
    void enc28j60EnableBroadcast( void ) {
    	erxfcon |= ERXFCON_BCEN;
    	enc28j60Write(ERXFCON, erxfcon);
    }
    
    void enc28j60DisableBroadcast( void ) {
    	erxfcon &= (0xff ^ ERXFCON_BCEN);
    	enc28j60Write(ERXFCON, erxfcon);
    }
    
    void enc28j60EnableMulticast( void ) {
    	erxfcon |= ERXFCON_MCEN;
    	enc28j60Write(ERXFCON, erxfcon);
    }
    
    void enc28j60DisableMulticast( void ) {
    	erxfcon &= (0xff ^ ERXFCON_MCEN);
    	enc28j60Write(ERXFCON, erxfcon);
    }
    
    
    // link status
    uint8_t enc28j60linkup(void)
    {
            // bit 10 (= bit 3 in upper reg)
    	return(enc28j60PhyReadH(PHSTAT2) && 4);
    }
    
    void enc28j60PacketSend(uint16_t len, uint8_t* packet)
    {
            // Check no transmit in progress
            while (enc28j60ReadOp(ENC28J60_READ_CTRL_REG, ECON1) & ECON1_TXRTS)
            {
                    // Reset the transmit logic problem. See Rev. B4 Silicon Errata point 12.
                    if( (enc28j60Read(EIR) & EIR_TXERIF) ) {
                            enc28j60WriteOp(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_TXRST);
                            enc28j60WriteOp(ENC28J60_BIT_FIELD_CLR, ECON1, ECON1_TXRST);
                    }
            }
    
    	// Set the write pointer to start of transmit buffer area
    	enc28j60WriteWord(EWRPTL, TXSTART_INIT);
    	// Set the TXND pointer to correspond to the packet size given
    	enc28j60WriteWord(ETXNDL, (TXSTART_INIT+len));
    	// write per-packet control byte (0x00 means use macon3 settings)
    	enc28j60WriteOp(ENC28J60_WRITE_BUF_MEM, 0, 0x00);
    	// copy the packet into the transmit buffer
    	enc28j60WriteBuffer(len, packet);
    	// send the contents of the transmit buffer onto the network
    	enc28j60WriteOp(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_TXRTS);
            // Reset the transmit logic problem. See Rev. B4 Silicon Errata point 12.
    }
    
    // just probe if there might be a packet
    //uint8_t enc28j60hasRxPkt(void)
    //{
    //       return enc28j60ReadByte(EPKTCNT) > 0;
    //}
    
    // Gets a packet from the network receive buffer, if one is available.
    // The packet will by headed by an ethernet header.
    //      maxlen  The maximum acceptable length of a retrieved packet.
    //      packet  Pointer where packet data should be stored.
    // Returns: Packet length in bytes if a packet was retrieved, zero otherwise.
    uint16_t enc28j60PacketReceive(uint16_t maxlen, uint8_t* packet)
    {
            	uint16_t rxstat;
    	uint16_t len;
    	// check if a packet has been received and buffered
    	//if( !(enc28j60Read(EIR) & EIR_PKTIF) ){
            // The above does not work. See Rev. B4 Silicon Errata point 6.
    	if( enc28j60Read(EPKTCNT) ==0 ){
    		return(0);
            }
    
    	// Set the read pointer to the start of the received packet
    	enc28j60WriteWord(ERDPTL, gNextPacketPtr);
    	//enc28j60Write(ERDPTL, (gNextPacketPtr &0xFF));
    	//enc28j60Write(ERDPTH, (gNextPacketPtr)>>8);
    	// read the next packet pointer
    	gNextPacketPtr  = enc28j60ReadBufferWord();
    	//gNextPacketPtr  = enc28j60ReadOp(ENC28J60_READ_BUF_MEM, 0);
    	//gNextPacketPtr |= enc28j60ReadOp(ENC28J60_READ_BUF_MEM, 0)<<8;
    	// read the packet length (see datasheet page 43)
    	len = enc28j60ReadBufferWord() - 4;
    	//len = enc28j60ReadOp(ENC28J60_READ_BUF_MEM, 0);
    	//len |= enc28j60ReadOp(ENC28J60_READ_BUF_MEM, 0)<<8;
            //len-=4; //remove the CRC count
    	// read the receive status (see datasheet page 43)
    	rxstat  = enc28j60ReadBufferWord();
    	//rxstat  = enc28j60ReadOp(ENC28J60_READ_BUF_MEM, 0);
    	//rxstat |= ((uint16_t)enc28j60ReadOp(ENC28J60_READ_BUF_MEM, 0))<<8;
    	// limit retrieve length
            if (len>maxlen-1){
                    len=maxlen-1;
            }
            // check CRC and symbol errors (see datasheet page 44, table 7-3):
            // The ERXFCON.CRCEN is set by default. Normally we should not
            // need to check this.
            if ((rxstat & 0x80)==0){
                    // invalid
                    len=0;
            }else{
                    // copy the packet from the receive buffer
                    enc28j60ReadBuffer(len, packet);
            }
    	// Move the RX read pointer to the start of the next received packet
    	// This frees the memory we just read out
    	enc28j60WriteWord(ERXRDPTL, gNextPacketPtr );
    	//enc28j60Write(ERXRDPTL, (gNextPacketPtr &0xFF));
    	//enc28j60Write(ERXRDPTH, (gNextPacketPtr)>>8);
            // However, compensate for the errata point 13, rev B4: enver write an even address!
            if ((gNextPacketPtr - 1 < RXSTART_INIT)
                    || (gNextPacketPtr -1 > RXSTOP_INIT)) {
                    enc28j60WriteWord(ERXRDPTL, RXSTOP_INIT);
                    //enc28j60Write(ERXRDPTL, (RXSTOP_INIT)&0xFF);
                    //enc28j60Write(ERXRDPTH, (RXSTOP_INIT)>>8);
            } else {
                    enc28j60WriteWord(ERXRDPTL, (gNextPacketPtr-1));
                    //enc28j60Write(ERXRDPTL, (gNextPacketPtr-1)&0xFF);
                    //enc28j60Write(ERXRDPTH, (gNextPacketPtr-1)>>8);
            }
    	// decrement the packet counter indicate we are done with this packet
    	enc28j60WriteOp(ENC28J60_BIT_FIELD_SET, ECON2, ECON2_PKTDEC);
    	return(len);
    
    }

ENC28J60.H

#ifndef __ENC28J60_H
    #define __ENC28J60_H
    
    #include "stm32f4xx.h"
    #include "Delay.h"
    
    #define disableChip  GPIO_SetBits(GPIOA,GPIO_Pin_4); delay_us(2);
    #define enableChip   GPIO_ResetBits(GPIOA,GPIO_Pin_4); delay_us(2);
    
    
    // ENC28J60 Control Registers
    // Control register definitions are a combination of address,
    // bank number, and Ethernet/MAC/PHY indicator bits.
    // - Register address        (bits 0-4)
    // - Bank number        (bits 5-6)
    // - MAC/PHY indicator        (bit 7)
    #define ADDR_MASK        0x1F
    #define BANK_MASK        0x60
    #define SPRD_MASK        0x80
    // All-bank registers
    #define EIE              0x1B
    #define EIR              0x1C
    #define ESTAT            0x1D
    #define ECON2            0x1E
    #define ECON1            0x1F
    // Bank 0 registers
    #define ERDPTL           (0x00|0x00)
    #define ERDPTH           (0x01|0x00)
    #define EWRPTL           (0x02|0x00)
    #define EWRPTH           (0x03|0x00)
    #define ETXSTL           (0x04|0x00)
    #define ETXSTH           (0x05|0x00)
    #define ETXNDL           (0x06|0x00)
    #define ETXNDH           (0x07|0x00)
    #define ERXSTL           (0x08|0x00)
    #define ERXSTH           (0x09|0x00)
    #define ERXNDL           (0x0A|0x00)
    #define ERXNDH           (0x0B|0x00)
    #define ERXRDPTL         (0x0C|0x00)
    #define ERXRDPTH         (0x0D|0x00)
    #define ERXWRPTL         (0x0E|0x00)
    #define ERXWRPTH         (0x0F|0x00)
    #define EDMASTL          (0x10|0x00)
    #define EDMASTH          (0x11|0x00)
    #define EDMANDL          (0x12|0x00)
    #define EDMANDH          (0x13|0x00)
    #define EDMADSTL         (0x14|0x00)
    #define EDMADSTH         (0x15|0x00)
    #define EDMACSL          (0x16|0x00)
    #define EDMACSH          (0x17|0x00)
    // Bank 1 registers
    #define EHT0             (0x00|0x20)
    #define EHT1             (0x01|0x20)
    #define EHT2             (0x02|0x20)
    #define EHT3             (0x03|0x20)
    #define EHT4             (0x04|0x20)
    #define EHT5             (0x05|0x20)
    #define EHT6             (0x06|0x20)
    #define EHT7             (0x07|0x20)
    #define EPMM0            (0x08|0x20)
    #define EPMM1            (0x09|0x20)
    #define EPMM2            (0x0A|0x20)
    #define EPMM3            (0x0B|0x20)
    #define EPMM4            (0x0C|0x20)
    #define EPMM5            (0x0D|0x20)
    #define EPMM6            (0x0E|0x20)
    #define EPMM7            (0x0F|0x20)
    #define EPMCSL           (0x10|0x20)
    #define EPMCSH           (0x11|0x20)
    #define EPMOL            (0x14|0x20)
    #define EPMOH            (0x15|0x20)
    #define EWOLIE           (0x16|0x20)
    #define EWOLIR           (0x17|0x20)
    #define ERXFCON          (0x18|0x20)
    #define EPKTCNT          (0x19|0x20)
    // Bank 2 registers
    #define MACON1           (0x00|0x40|0x80)
    #define MACON2           (0x01|0x40|0x80)
    #define MACON3           (0x02|0x40|0x80)
    #define MACON4           (0x03|0x40|0x80)
    #define MABBIPG          (0x04|0x40|0x80)
    #define MAIPGL           (0x06|0x40|0x80)
    #define MAIPGH           (0x07|0x40|0x80)
    #define MACLCON1         (0x08|0x40|0x80)
    #define MACLCON2         (0x09|0x40|0x80)
    #define MAMXFLL          (0x0A|0x40|0x80)
    #define MAMXFLH          (0x0B|0x40|0x80)
    #define MAPHSUP          (0x0D|0x40|0x80)
    #define MICON            (0x11|0x40|0x80)
    #define MICMD            (0x12|0x40|0x80)
    #define MIREGADR         (0x14|0x40|0x80)
    #define MIWRL            (0x16|0x40|0x80)
    #define MIWRH            (0x17|0x40|0x80)
    #define MIRDL            (0x18|0x40|0x80)
    #define MIRDH            (0x19|0x40|0x80)
    // Bank 3 registers
    #define MAADR1           (0x00|0x60|0x80)
    #define MAADR0           (0x01|0x60|0x80)
    #define MAADR3           (0x02|0x60|0x80)
    #define MAADR2           (0x03|0x60|0x80)
    #define MAADR5           (0x04|0x60|0x80)
    #define MAADR4           (0x05|0x60|0x80)
    #define EBSTSD           (0x06|0x60)
    #define EBSTCON          (0x07|0x60)
    #define EBSTCSL          (0x08|0x60)
    #define EBSTCSH          (0x09|0x60)
    #define MISTAT           (0x0A|0x60|0x80)
    #define EREVID           (0x12|0x60)
    #define ECOCON           (0x15|0x60)
    #define EFLOCON          (0x17|0x60)
    #define EPAUSL           (0x18|0x60)
    #define EPAUSH           (0x19|0x60)
    // PHY registers
    #define PHCON1           0x00
    #define PHSTAT1          0x01
    #define PHHID1           0x02
    #define PHHID2           0x03
    #define PHCON2           0x10
    #define PHSTAT2          0x11
    #define PHIE             0x12
    #define PHIR             0x13
    #define PHLCON           0x14
    
    // ENC28J60 ERXFCON Register Bit Definitions
    #define ERXFCON_UCEN     0x80
    #define ERXFCON_ANDOR    0x40
    #define ERXFCON_CRCEN    0x20
    #define ERXFCON_PMEN     0x10
    #define ERXFCON_MPEN     0x08
    #define ERXFCON_HTEN     0x04
    #define ERXFCON_MCEN     0x02
    #define ERXFCON_BCEN     0x01
    // ENC28J60 EIE Register Bit Definitions
    #define EIE_INTIE        0x80
    #define EIE_PKTIE        0x40
    #define EIE_DMAIE        0x20
    #define EIE_LINKIE       0x10
    #define EIE_TXIE         0x08
    #define EIE_WOLIE        0x04
    #define EIE_TXERIE       0x02
    #define EIE_RXERIE       0x01
    // ENC28J60 EIR Register Bit Definitions
    #define EIR_PKTIF        0x40
    #define EIR_DMAIF        0x20
    #define EIR_LINKIF       0x10
    #define EIR_TXIF         0x08
    #define EIR_WOLIF        0x04
    #define EIR_TXERIF       0x02
    #define EIR_RXERIF       0x01
    // ENC28J60 ESTAT Register Bit Definitions
    #define ESTAT_INT        0x80
    #define ESTAT_LATECOL    0x10
    #define ESTAT_RXBUSY     0x04
    #define ESTAT_TXABRT     0x02
    #define ESTAT_CLKRDY     0x01
    // ENC28J60 ECON2 Register Bit Definitions
    #define ECON2_AUTOINC    0x80
    #define ECON2_PKTDEC     0x40
    #define ECON2_PWRSV      0x20
    #define ECON2_VRPS       0x08
    // ENC28J60 ECON1 Register Bit Definitions
    #define ECON1_TXRST      0x80
    #define ECON1_RXRST      0x40
    #define ECON1_DMAST      0x20
    #define ECON1_CSUMEN     0x10
    #define ECON1_TXRTS      0x08
    #define ECON1_RXEN       0x04
    #define ECON1_BSEL1      0x02
    #define ECON1_BSEL0      0x01
    // ENC28J60 MACON1 Register Bit Definitions
    #define MACON1_LOOPBK    0x10
    #define MACON1_TXPAUS    0x08
    #define MACON1_RXPAUS    0x04
    #define MACON1_PASSALL   0x02
    #define MACON1_MARXEN    0x01
    // ENC28J60 MACON2 Register Bit Definitions
    #define MACON2_MARST     0x80
    #define MACON2_RNDRST    0x40
    #define MACON2_MARXRST   0x08
    #define MACON2_RFUNRST   0x04
    #define MACON2_MATXRST   0x02
    #define MACON2_TFUNRST   0x01
    // ENC28J60 MACON3 Register Bit Definitions
    #define MACON3_PADCFG2   0x80
    #define MACON3_PADCFG1   0x40
    #define MACON3_PADCFG0   0x20
    #define MACON3_TXCRCEN   0x10
    #define MACON3_PHDRLEN   0x08
    #define MACON3_HFRMLEN   0x04
    #define MACON3_FRMLNEN   0x02
    #define MACON3_FULDPX    0x01
    // ENC28J60 MICMD Register Bit Definitions
    #define MICMD_MIISCAN    0x02
    #define MICMD_MIIRD      0x01
    // ENC28J60 MISTAT Register Bit Definitions
    #define MISTAT_NVALID    0x04
    #define MISTAT_SCAN      0x02
    #define MISTAT_BUSY      0x01
    // ENC28J60 PHY PHCON1 Register Bit Definitions
    #define PHCON1_PRST      0x8000
    #define PHCON1_PLOOPBK   0x4000
    #define PHCON1_PPWRSV    0x0800
    #define PHCON1_PDPXMD    0x0100
    // ENC28J60 PHY PHSTAT1 Register Bit Definitions
    #define PHSTAT1_PFDPX    0x1000
    #define PHSTAT1_PHDPX    0x0800
    #define PHSTAT1_LLSTAT   0x0004
    #define PHSTAT1_JBSTAT   0x0002
    // ENC28J60 PHY PHCON2 Register Bit Definitions
    #define PHCON2_FRCLINK   0x4000
    #define PHCON2_TXDIS     0x2000
    #define PHCON2_JABBER    0x0400
    #define PHCON2_HDLDIS    0x0100
    
    // ENC28J60 Packet Control Byte Bit Definitions
    #define PKTCTRL_PHUGEEN  0x08
    #define PKTCTRL_PPADEN   0x04
    #define PKTCTRL_PCRCEN   0x02
    #define PKTCTRL_POVERRIDE 0x01
    
    // SPI operation codes
    #define ENC28J60_READ_CTRL_REG       0x00
    #define ENC28J60_READ_BUF_MEM        0x3A
    #define ENC28J60_WRITE_CTRL_REG      0x40
    #define ENC28J60_WRITE_BUF_MEM       0x7A
    #define ENC28J60_BIT_FIELD_SET       0x80
    #define ENC28J60_BIT_FIELD_CLR       0xA0
    #define ENC28J60_SOFT_RESET          0xFF
    
    
    // The RXSTART_INIT should be zero. See Rev. B4 Silicon Errata
    // buffer boundaries applied to internal 8K ram
    // the entire available packet buffer space is allocated
    //
    // start with recbuf at 0/
    #define RXSTART_INIT     0x0
    // receive buffer end
    #define RXSTOP_INIT      (0x1FFF-0x0600-1)
    // start TX buffer at 0x1FFF-0x0600, pace for one full ethernet frame (~1500 bytes)
    #define TXSTART_INIT     (0x1FFF-0x0600)
    // stp TX buffer at end of mem
    #define TXSTOP_INIT      0x1FFF
    //
    // max frame length which the conroller will accept:
    #define        MAX_FRAMELEN        1500        // (note: maximum ethernet frame length would be 1518)
    //#define MAX_FRAMELEN     600
    
    uint8_t enc28j60ReadOp(uint8_t op, uint8_t address);
    
    
    // functions
    extern uint8_t enc28j60ReadOp(uint8_t op, uint8_t address);
    extern void enc28j60WriteOp(uint8_t op, uint8_t address, uint8_t data);
    extern void enc28j60ReadBuffer(uint16_t len, uint8_t* data);
    extern void enc28j60WriteBuffer(uint16_t len, uint8_t* data);
    extern void enc28j60SetBank(uint8_t address);
    extern uint8_t enc28j60Read(uint8_t address);
    extern void enc28j60Write(uint8_t address, uint8_t data);
    extern void enc28j60PhyWrite(uint8_t address, uint16_t data);
    extern void enc28j60clkout(uint8_t clk);
    extern void enc28j60SpiInit(void);//
    extern void enc28j60Init(uint8_t* macaddr);
    extern void enc28j60PacketSend(uint16_t len, uint8_t* packet);
    extern uint16_t enc28j60PacketReceive(uint16_t maxlen, uint8_t* packet);
    extern uint8_t enc28j60getrev(void);
    
    extern uint8_t enc28j60hasRxPkt(void);
    extern uint8_t enc28j60linkup(void);
    extern void enc28j60EnableBroadcast( void );
    extern void enc28j60DisableBroadcast( void );
    extern void enc28j60EnableMulticast( void );
    extern void enc28j60DisableMulticast( void );
    extern void enc28j60PowerDown(void);
    extern void enc28j60PowerUp(void);
    
    #endif /* __ENC28J60_H */

拍了个小视频：

[http://pan.baidu.com/s/1rDkHq ][http_pan.baidu.com_s_1rDkHq]

密码:95cm

再结合点传感器，或许会发现有点智能家居的影子！

[20131002013511953]: /images/20220828/70986aa2e2ff4a058b356935d080fff1.png
[20131002014151765]: /images/20220828/775ea7cf8a824de29e08e9033ae2ff57.png
[http_pan.baidu.com_s_1rDkHq]: http://pan.baidu.com/s/1rDkHq