harbor从v1.1.1升级到v1.5.1的记录(二)

小咪咪 2022-05-18 06:54 201阅读 0赞

看完上一遍是habror升级之同步数据，接下来我们就讲部署的注意事项

下载在线升级的harborv1.5.1 [harbor-online-installer-v1.5.1.tgz][]

解压

tar xvf harbor-online-installer-v1.5.1.tgz

修改配置文件`harbor.cfg`

因为harborv1.1.1 和v1.5.1相比较，v1.5.1新增了镜像邵渺功能，复制的策略也有改变，定时，立即等同步策略，这个功能可用可不用

因此，主要注意的地方就是修改相关的镜像存储的配置，harbor v1.1.1的registry的配置文件主要修改config.yaml文件

由之前的v1.1.1版本的修改文件 `common/templates/registry/config.yml`

storage:
        s3:
            accesskey: xxx
            secretkey: xxx
            region: xx
            regionendpoint: url 
            bucket: registrybucket
            encrypt: false
            secure: false
            v4auth: true
            chunksize: 5242880
            multipartcopychunksize: 33554432
            multipartcopymaxconcurrency: 100
            multipartcopythresholdsize: 33554432
        cache:
            blobdescriptor: redis
    # filesystem:
    # rootdirectory: /storage
        maintenance:
            uploadpurging:
                enabled: false
        delete:
            enabled: true

改为harbor v1.5.1的配置，如下

storage:
      cache:
        blobdescriptor: redis
      $storage_provider_info
      maintenance:
        uploadpurging:
          enabled: false
      delete:
        enabled: true
        ...
        ...
    redis:
      addr: 192.168.1.11:6379
      db: 2
      dialtimeout: 10ms
      readtimeout: 10ms
      writetimeout: 10ms
      pool:
        maxidle: 16
        maxactive: 64
        idletimeout: 300s

通过修改registry相关的配置

### Docker Registry setting ###
    #registry_storage_provider can be: filesystem, s3, gcs, azure, etc.
    registry_storage_provider_name = s3
    #registry_storage_provider_config is a comma separated "key: value" pairs, e.g. "key1: value, key2: value2".
    #Refer to https://docs.docker.com/registry/configuration/#storage for all available configuration.
    registry_storage_provider_config = accesskey: xxx, secretkey: xxx, region: lfrz1, regionendpoint: http:xxxx, bucket: registrybucket, encrypt: false, secure: false, v4auth: true, chunksize: 5242880, multipartcopychunksize: 33554432, multipartcopymaxconcurrency: 100, multipartcopythresholdsize: 33554432

还要注意ui加密的key也得复制过来,默认在`/data/secretkey`这个文件里，高可用时 也要注意这个的一致性

[root@harbor151 harbor]# cat /data/secretkey 
    6d70UIQ8FRDxxsGp[root@harbor151 harbor]#

然后在安装目录，直接执行

./install.sh

就升级成功了，另外还有相关的接口改变，根据具体的业务修改相应的接口信息  
完毕

参考：  
[installation\_guide][installation_guide]

[harbor-online-installer-v1.5.1.tgz]: https://storage.googleapis.com/harbor-releases/harbor-online-installer-v1.5.1.tgz
[installation_guide]: https://github.com/vmware/harbor/blob/master/docs/installation_guide.md