redis 报错 Redis protected-mode 配置文件没有真正启动

偏执的太偏执、 2021-08-19 12:59 733阅读 0赞

### 文章来源： ###

> [https://blog.csdn.net/Agly\_Clarlie/article/details/52251746][https_blog.csdn.net_Agly_Clarlie_article_details_52251746]

[https://blog.csdn.net/Agly\_Clarlie/article/details/52251746][https_blog.csdn.net_Agly_Clarlie_article_details_52251746]

[https://blog.csdn.net/fly43108622/article/details/52972433][https_blog.csdn.net_fly43108622_article_details_52972433]

问题表象：

(error) DENIED Redis is running in protected mode because protected mode is enabled

*  1

问题解决方法：

Redis protected-mode 是3.2 之后加入的新特性，在Redis.conf的注释中，我们可以了解到，他的具体作用和启用条件

链接redis 时只能通过本地localhost (127.0.0.1）这个来链接，而不能用网络ip(192.168…)这个链接，问题然如果用网络ip 链接会报以下的错误：

(error) DENIED Redis is running in protected mode because protected mode is enabled, no bind address was specified, no authentication password is requested to clients.  
In this mode connections are only accepted from the lookback interface. If you want to connect from external computers to Redis you may adopt one of the following solutions:

1.  Just disable protected mode sending the command ‘CONFIG SET protected-mode no’ from the loopback interface by connecting to Redis from the same host the server is running, however MAKE SURE Redis is not publicly accessible from internet if you do so. Use CONFIG REWRITE to make this change permanent.
2.  Alternatively you can just disable the protected mode by editing the Redis configuration file, and setting the protected mode option to ‘no’, and then restarting the server.
3.  If you started the server manually just for testing, restart it with the --portected-mode no option.
4.  Setup a bind address or an authentication password. NOTE: You only need to do one of the above things in order for the server to start accepting connections from the outside.

是说处于保护模式，只能本地链接，我们需要修改配置文件…/redis.conf

**注：redis.config 只是让我们修改自定义配置的模板，默认redis-server启动时读取的是默认的参数配置，与该文件无关，所以修改该文件后，需要指定 redis-server  redis conf 启动才能生效：**

1)打开配置文件把下面对应的注释掉

# bind 127.0.0.1

*  1

2)Redis默认不是以守护进程的方式运行，可以通过该配置项修改，使用yes启用守护进程，本次设置为no

daemonize no

*  1

3)保护模式

protected-mode no

*  1

4)最后关键的是：  
没反应应该是你启动服务端的时候没有带上配置文件。你可以./redis-server redis.conf  
你配置好了，但要重新启动redis,如果还是报一样的错误，很可能是没有启动到配置文件，所以需要真正的和配置文件启动需要：  
在redis.conf文件的当前目录下：

$ redis-server redis.conf

*  1

如果还是所某个端口已在使用，那么可能是有 后台程序在占用该端口，需要kill 掉该程序，重新带上配置文件。./redis-server redis.conf启动。  
将含有”redis”关键词的进程杀死:

$ ps -ef | grep redis | awk ‘{print $2}’ | xargs kill -9

[https_blog.csdn.net_Agly_Clarlie_article_details_52251746]: https://blog.csdn.net/Agly_Clarlie/article/details/52251746
[https_blog.csdn.net_fly43108622_article_details_52972433]: https://blog.csdn.net/fly43108622/article/details/52972433